Pontiac G6 Starter Kill Switch

Pontiac G6 Starter Kill Switch

Check from the starter solenoid relay to the solenoid, and make sure the ignition switch connections are still good, and the switch itself is. The most obvious warning sign that a problem with the starter relay exists is when the vehicle won't start when you engage the ignition process.


2012 Ford focus titanium transmission failure problem

Clicking this will make more experts see the question and we will remind you when it gets answered.

Pontiac g6 starter kill switch. First thing in the morning you can start and kill it and start it up until. My last alternative would be under the ho However, when powered, it should send a signal to the starter relay once the key is turned or the starter button is pressed.

When the ignition switch is turned to the start position, the body control module (bcm) receives battery voltage on the. Even if your car doesn't have the remote start your starter is still computer controlled. (2006 g6 gt) once the engine gets hot (catalyst) the starter heat soaks and will not crank until it cools down.

Most cars have a direct link between the ignition switch and the starter. Check if this fits your 2010 pontiac g6. The ignition switch does not directly control the starter motor like in older designs.

I got a 09 pontiac g6 wont start.there is no crank no. The starter is literally 2 inches from the catalytic converter on the 3.5 v6. After driving my 2006 g6 gtp for a long while after killing it it won't start back up until you let it set for a while.

Test the ground circuits of the module that is not communicating for an open. Norm answered 7 years ago. I have since installed a heat shield and the occurrences have reduced.

Have a pontiac g6 the starter just clicks once when i turn the key if i leave the key in the start position sometimes it starts is this a starter problem. If your alternator has a bad diode, your battery can drain. So recently bought a 2007 3.5l g6 and it was starting fine when i first bought it but it needed a neutral safety switch so i already planned to replace it.

Have the starter motor tested. As stated above, electronic keys do not have a manual ignition switch. You have know idea how the starting system works , an with the engine light on your best bet would be to have it towed to a qualified repair shop.

Asked by jetnate33 apr 18, 2012 at 10:33 am about the 2006 pontiac g6 base v6 question type: Posted by vincent calanni on jul 22, 2015. If however your battery tests okay, do this:

If the module is the body control module (bcm), test its class 2 serial data circuit for an open, also. These cars will not start and the security system will not reset with less than 12.6 volts. Turn the key to the on position and leave it for ten minutes.

If your car's immobilizer has been activated, it can sometimes be difficult to reset. You may need a diagram and a test light to check the circuit. Control module references for the applicable schematic.

Sign up for the case ». If you can hear a click sound when turning the ignition key before the fuse blows, probably the relay is good. So one day it just wouldn't start checked all the fuses and the battery and all of that was fine.the security light wasnt on.

This will 'reset' the ignition rotation sensor, which often goes. Defendant (s) general motors company. Therefore if you hold the key it will crank as long as you hold the key.

The starting procedure on these vehicles is fairly complicated and the root problem lies in the ignition switch. District court for the southern district of new york. I have the clifford matrix rs1.1 with the security bypass module.

The g6 has a pcu controlled system. 13 people found this helpful. Make sure you have at least 12.6 volts at the battery.

The starter is different on our cars because of the integrated remote start. Check if this fits your 2010 pontiac g6. Maintenance & repair i took the key out and got out my car and realized my car is still running the only way to shut it off was rev the engine and let it stall out what could that be

Already replaced the starter and all the relays but same problem. Seems like no signal going to the starter. When you turn the key nothing happens except all the lights and gauges come on like normal.


284 best images about Car on Pinterest Car stuff, Car


ACDelco 2SD41XE Professional Positive Battery Cable To


Neutral safety switch 8454006010 for Toyota Lexus Pontiac


Blessing others one project at


Trunk Release Switch 4F1927227A/B0508A6L Trunk Lid

Leave a Reply

Your email address will not be published.